KICKER CX SERIES - VERTICAL INSTALL AMPLIFIERS

Tone controls for the best sound

Separate high- and low-pass filters on the front and rear channels help you sculpt the sound to get the most out of all your speakers. Variable bass boosts, also on both the front and rear channels, allow you to add some low-end punch when you're running subs. If you're using the rear channels to drive a subwoofer, an optional wired remote lets you control the level from the front seat.

Hooks in almost anywhere in almost any position

Kicker's Fail-Safe Integration Technology (FIT™) keeps this amp's input free from noise or interference, so you can tap into your vehicle's speaker wiring for an input signal without a worry. A 3-second turn-on/turn-off delay eliminates system pops and other noises. The CXA360.4T comes with hardware that lets you mount it vertically, so you can put it in a location that takes up very little floor space and looks cool too.

• Class A/B full-range channels
• Three-second turn-on/off delay to eliminate unwanted interference
• Variable 12dB crossovers provides control to dial in perfect sound
• KickEQ™ 6dB variable bass boost for those additional low frequencies
• FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
• Accepts up to 40-volt input signal
• Small footprint for easier installation
• Vertical mounting hardware included for another unique look
• Compatible with CXARC Remote Bass Control (AMP2 must be in LO-PASS X-OVER mode

SPECIFICATIONS

• Model: CXA360.4
• Power(watts/ch) 4 Ohm Stereo: 65x4
• Power(watts/ch) 4 Ohm Stereo: 90x4
• Power(watts/ch) 4 Ohm Mono: 180x2
• Dimensions: 12 1/2 in, 31.7 cm
• Frequency Response (Hz): 10HZ
• Input Sensitivity: 125mV-5V (Low Level), 1V-40V (High Level)
• Signal-to-Noise Ratio: 95dB
• Active Crossover: HI, LO or OFF; Variable 50-200Hz @ 12dB/Octave

Tone controls for the best sound

Separate high-pass filters on the front and rear channels help you sculpt the sound to get the most out of your speakers. A variable low-pass and a fixed subsonic filter help you tune the bass for your sub, enclosure, and vehicle, while a variable bass boost allows you to add some low-end punch. An optional wired remote lets you conveniently adjust the subwoofer level from your front seat.

Hooks in almost anywhere in almost any position

Kicker's Fail-Safe Integration Technology (FIT™) keeps this amp's input free from noise or interference, so you can tap into your speaker wires for a signal without a worry. A 3-second turn-on/turn-off delay eliminates system pops and other noises. The CXA660.5T comes with hardware that lets you mount it vertically, so you can put it in a location that takes up very little floor space and looks cool too.

PRODUCT HIGHLIGHTS

• 5-channel marine amplifier
• 75 watts RMS x 4 + 200 watts RMS x 1 at 4 ohms
• 125 watts RMS x 4 at 2 ohms + 400 watts RMS x 1 at 1 or 2 ohms
• 250 watts RMS x 2 bridged at 4 ohms + 400 watts RMS x 1 at 2 ohms
• subwoofer channel 1-ohm stable — 400 watts RMS (+/-10%) x 1 at 1 ohm)
• Class D amp technology
• gain knobs also function as clip lights
• Amp 1: variable high- or low-pass filter (10-500 Hz, 24 dB/octave), plus 10x switch
• Amp 2: variable high-pass (10-500 Hz, 24 dB/octave), low-pass (40-500 Hz, 24 dB/octave with 10x switch), or bandpass (engages both) filter
• Sub channel: variable low-pass filter (40-160 Hz, 24 dB/octave), subsonic filter (10-80 Hz, 24 dB/octave), and variable bass boost (0-6 dB at 40 Hz)
• wired remote bass knob control